21
Calculations & Checks / Re: Parallel conductor It(A) critical message
« Last post by jw on 10 November 2023, 21:13 »Spacing the cables, if possible, can help as the grouping factor will not be considered
Recent Posts
22
Calculations & Checks / Re: Parallel conductor It(A) critical message
« Last post by Mert on 08 November 2023, 10:38 »EOM calculates and displays the result for one conductor of a parallel bunch, so, what you see is the current would pass through via one conductor of the whole bunch. To remove this you need to reconsider your cross-sections.
23
Calculations & Checks / Parallel conductor It(A) critical message
« Last post by mattwilson83 on 08 November 2023, 09:44 »I always get a critical message when using parallel conductors, the It(A) is only calculating the single conductor and not the parallel conductor. Is there a way to clear the critical warning.
24
ElectricalOM for New Users / Re: Consumer Unit Schedules
« Last post by Unknown on 06 November 2023, 14:30 »Hi
Thanks for the update. That looks ideal for our needs.
Thanks for the update. That looks ideal for our needs.
25
ElectricalOM for New Users / Re: Consumer Unit Schedules
« Last post by admin on 06 November 2023, 13:56 »Hello,
We made some changes and the Excel-based report will work as expected with extension boards. This will be available in the upcoming update. Please see the image below:
We made some changes and the Excel-based report will work as expected with extension boards. This will be available in the upcoming update. Please see the image below:
26
ElectricalOM for New Users / Consumer Unit Schedules
« Last post by Unknown on 03 November 2023, 10:40 »Hi Mert
Thanks for the reply. I think the excel templates will be very useful.
I've just been trying out the ones already in ElecOM and I have a number of boards with an 'extension board' but they are not recognised as split boards for the excel templates. They are recognised as a DB but don't display the extension board part. Am I doing something wrong?
Thanks for the reply. I think the excel templates will be very useful.
I've just been trying out the ones already in ElecOM and I have a number of boards with an 'extension board' but they are not recognised as split boards for the excel templates. They are recognised as a DB but don't display the extension board part. Am I doing something wrong?
27
ElectricalOM for New Users / Re: Consumer Unit Schedules
« Last post by Mert on 03 November 2023, 10:06 »"Is there any way to avoid this and just start the numbering again?"
Simple answer is not at the moment.
"I'd like to try and make the ElecOM output more like the other image"
You can use custom report excel templates to create your own format. you can find the codes used for various data here:
https://electricalom.com/site/knowledgebase.php?action=displayarticle&id=137
Simple answer is not at the moment.
"I'd like to try and make the ElecOM output more like the other image"
You can use custom report excel templates to create your own format. you can find the codes used for various data here:
https://electricalom.com/site/knowledgebase.php?action=displayarticle&id=137
28
ElectricalOM for New Users / Consumer Unit Schedules
« Last post by Unknown on 03 November 2023, 09:24 »We've had feedback from some clients regarding how we show split load consumer units with the extension board. Generally it's found to be confusing with the split section having a prefix of the way it was added to, e.g. by adding the extension board to way 9, all ways then become 9.1, 9.2, 9.3 etc.
Is there any way to avoid this and just start the numbering again?
We also are struggling with how RCD protective devices are shown for split load consumer units. Below are two screenshots. One using ElecOM and one using a different software package. I'd like to try and make the ElecOM output more like the other image as it's easier to understand. Does anyone know any better ways of setting up the reports?
Is there any way to avoid this and just start the numbering again?
We also are struggling with how RCD protective devices are shown for split load consumer units. Below are two screenshots. One using ElecOM and one using a different software package. I'd like to try and make the ElecOM output more like the other image as it's easier to understand. Does anyone know any better ways of setting up the reports?
29
ElectricalOM for New Users / Re: Unable to import Easycert files
« Last post by Mert on 09 October 2023, 08:03 »Hi MBESSEBM,
Please use the latest beta and see if it works. If not, send your file to support@modecsoft.com for further inspection, please.
Please use the latest beta and see if it works. If not, send your file to support@modecsoft.com for further inspection, please.
30
ElectricalOM for New Users / Unable to import Easycert files
« Last post by MBESSEBM on 08 October 2023, 09:18 »Hi all,
I'm currently having an issue with importing DB's across to EOM.
I have followed the steps correctly as shown in the guides available but I get a blank DB schedule with nothing to select.
My process is:
EOM > File > Import > Tysoft EasyCert > Select EasyCert File > "Tysoft Import DBs
The box completely blank.
I have tried both complex commercial installations and very simple domestic installations yet neither will show a selectable DB.
Can anyone point me in the right direction please.
I'm currently having an issue with importing DB's across to EOM.
I have followed the steps correctly as shown in the guides available but I get a blank DB schedule with nothing to select.
My process is:
EOM > File > Import > Tysoft EasyCert > Select EasyCert File > "Tysoft Import DBs
The box completely blank.
I have tried both complex commercial installations and very simple domestic installations yet neither will show a selectable DB.
Can anyone point me in the right direction please.